Florida generator guide
Your Generator's Transfer Switch May Have Shipped Without the Load Control You Were Promised
Updated November 16, 2026
A tech out servicing a two-year-old heat pump looked at the big new standby generator sitting next to it and asked the homeowner one question: where's your load shed module? The homeowner had no answer. That silence is the whole problem in a sentence. A transfer switch that looks finished on the wall but has nothing inside it to stop your air conditioner from dragging the generator down. Here's how to tell whether yours came with that part, or without it.
About five minutes. No salesman, no all-day window.
The switch on the wall looked complete. It wasn't.
Picture an installer popping the cover off a fresh 200-amp transfer switch, the gray box that decides whether your house runs on the street or on the generator. Everything's landed, everything's neat. And then he notices the one thing that isn't there: the piece that manages your biggest loads so they don't all pile onto the generator at once.
Here's where it gets confusing. Some of Generac's whole-home switches come with that brain already built in. They call it the Smart A/C Module, and one of them can babysit up to four central air conditioners with no extra hardware bolted on. But not every 200-amp switch ships that way. Plenty of them are just a switch. They flip your house over to generator power and nothing more. The load control is a separate module somebody has to add, wire, and set.
So you end up with two boxes that look almost identical from your driveway, and only one of them is actually watching your AC. That's exactly why a real homeowner got caught flat-footed when his HVAC tech pointed and asked where the module was. He'd been told the switch handled it, and nobody had checked.
Why the air conditioner is the thing that trips it
Your AC doesn't sip power. When that compressor kicks on, it yanks a huge gulp of electricity for a half-second to get moving. Think of a stalled car getting shoved from a dead stop, that one brutal heave before it rolls. The running draw after that is modest. It's the kick that's the problem.
A generator feels that kick as its engine bogging down. Power doesn't just blink. The frequency sags, the whole output softens for a beat. According to Generac's transfer switch manual, the load control watches for exactly this: when the frequency drops below 58 hertz and stays there for three seconds, it reads that as the generator starting to drown, and it acts. No module, nothing's watching, and in a Florida August with two AC units trying to start against a well pump, the generator can stall itself in the dark.
And this is the part that catches people who bought big on purpose. A 200-amp home would need somewhere around 48 kilowatts to run every single circuit at the same instant, a generator the size of a refrigerator. Erayak Power puts it plainly: most homes that size run fine on 22 to 26 kilowatts, but only with load management doing the juggling. Take the juggler out and even a large generator can get swamped the moment the house asks for everything at once.
What that little module actually does
It's smaller than you'd expect for the job, which is why one commenter looked at his and said it seemed too dinky to handle a 70-amp AC breaker. But it never touches that heavy power. It plays a quieter trick.
Inside, it taps the thin low-voltage wire that runs from your thermostat to the AC, the 24-volt signal, the one that tells the unit "turn on." When the generator starts to strain, the module just interrupts that whisper. The AC never gets the message to start, so it waits. A few minutes later, when the coast is clear, the signal comes back and the unit cycles on like nothing happened. You keep the lights, the fridge, the fans. The AC takes turns instead of taking the whole generator down.
And you can stack them in a pecking order: the bedroom unit set to come back first, the garage last, your well pump somewhere in the line. The generator stops being a thing that either covers everything or chokes, and becomes a thing that spends what it has on what matters first.
The only way to know for sure: your address, one price
You can't tell from the driveway. Two switches that look the same, one watching your AC and one blind to it. The difference is inside the box and in how it was wired. The homeowner who got asked about his module had to go track down his installer to even find out.
GENERasic skips the guessing. Instead of a size range and a "depends," you get one committed installed price for your specific house: the generator, the right transfer switch, and the load control it actually needs so your AC can't stall it. Put in your address and get your price. No tech standing in your yard asking a question you can't answer.
Common questions
My HVAC tech asked where my load shed module was and I couldn't answer. Do I even have one?
Maybe, maybe not, and you can't tell by looking at the box on the wall. Some whole-home transfer switches have the load control built in; many don't and need a separate module added. The reliable way to know is to have someone open the switch and confirm whether the module is there and wired to your AC. If a tech asked the question, it's worth checking rather than assuming.
I bought a big generator, 24 or 26 kW. Do I still need load management?
Often yes. Running every circuit in a 200-amp home at once can call for roughly 48 kW. Most homes that size run fine on 22 to 26 kW, but that math only works because load management keeps your biggest loads from all starting at the same second. A large generator with nothing managing the loads can still get swamped when the AC, the dryer, and a well pump all kick at once.
Will a load shed module work with an older Generac Guardian, or a different brand of generator?
Generally yes. These modules work off the generator's frequency, and standby generators in the US run at the same 60-ish hertz, so the module reacts to the engine bogging down regardless of the badge. Owners have added them to Generac units many years old. Have an installer confirm the wiring for your exact setup.
Does the module shut my air conditioning off during the whole outage?
No. It only pauses the AC in the moment the generator is straining, by briefly interrupting the low-voltage thermostat signal. Once there's room, the signal returns and the AC cycles back on. During a normal outage you'd barely notice it. It's managing the few seconds of overlap, not killing your cooling for the night.
The module looks tiny. How can it handle a 70-amp AC circuit?
It doesn't carry that heavy power at all. It taps the thin 24-volt wire between your thermostat and the air conditioner and simply withholds the "start" signal when needed. The big current never passes through the module, which is why a small device can manage a large AC load without being large itself.
Sources
- Generac Power Systems (Automatic Transfer Switch Owner's Manual) — Loads are shed when frequency is less than 58 Hz for three seconds or less than 50 Hz for 1/2 second (for 60 Hz systems).
- Erayak Power — A 200-amp home service needs about 48kW to cover every circuit at full capacity, but most homes that size run fine on 22kW to 26kW with load management.
- Norwall PowerSystems — The integrated Smart A/C Module allows the Generac transfer switch to manage 4 central air conditioners with no additional hardware required.
- GeneratorMagic — Internal normally closed relays interrupt the 24 VAC thermostat control signal to disable the air conditioner load; loads to be shed are set in priority levels.
Stop reading ranges. Get your number.
GENERasic pulls the real property, flood, and elevation data for your exact address and returns one all-in installed price — sized to your home, your fuel, and your flood elevation. The vetted local installer confirms it on site.
Get your installed price →More answers
- Why Your Generator Shows an ‘Undervoltage’ Code — And Why It’s Usually Not the Grid
- Generac Fault Code 1100 (Overcrank): What It Actually Means
- Generac Fault Code 1300 (Low Oil Pressure Shutdown): Is Your Engine Actually Low on Oil?
- What an Automatic Transfer Switch Actually Does — and Why a Generator Without One Is Just a Loud Box in the Yard
- Are Home Standby Generators Just for Hurricanes? The Outages That Actually Run Them Most
- Do Standby Generators Actually Need Maintenance? (And Why Nobody Mentioned It at the Sale)
- "Annual Service" Isn't in Generac's Manual — But in Florida, the Footnote Puts It There
- Generac Fault Code 1400 (High Temperature Shutdown): Why an Air-Cooled Unit Overheats After Years of Working Fine
- Generac Fault Code 1505: Why "RPM Sense Loss" Almost Never Means a Bad Sensor
- Generac Undervoltage Codes 1900, 1901 & 1902: The One Test Before You Buy a Single Part
- Generac Fault Code 1906 (Waveform Error): What a 'Dirty' Power Signal Really Means
- Generac Fault Code 2299 (Overload at Startup): Why It Trips the Instant the Load Hits
- Generac Fault Code 2800: What It Means (and Why It's Rarely the Engine)
- Why Your Generator 'Overspeeds' and Shuts Down When Nothing Seems Wrong
- Green Light vs. Yellow Light on Your Standby Generator: What Each One Actually Promises
- The Yellow Maintenance Light: What Happens If You Just Ignore It
- What 'Whole-Home Generator' Actually Means (and Why the Phrase Is a Trap)
- Why Square Footage Is the Wrong Way to Size Your Standby Generator
- Gas or Electric? Your Appliances Are Quietly Picking Your Generator Size
- Why the Same Generator Makes Less Power in the Mountains Than in Florida
- How a Book-Sized Box Lets a 22kW Generator Run a 30kW House
- Why the Same Florida House Can Take Two Very Different Generators
- Your Generator Runs But the AC Won't Start: The Inrush Problem
- The $300 Part That Shrinks the Generator Your Florida AC Needs
- Air-Cooled vs Liquid-Cooled Standby Generators: Which One You Actually Need
- The '50% Load' Fuel Myth: Why the Generator Spec Sheet Misleads You
- How Long Will My Propane Tank Actually Run My Generator?
- Two Generators, Same House, Very Different Fuel Bills
- Natural Gas vs Propane for a Standby Generator: The Tradeoff Nobody Explains
- What a Clogged Air Filter Really Does to Your Generator
- Why a Spotless Air Filter Still Chokes Your Generator in Florida
- The One Spark That Decides Whether Your Generator Wakes Up
- Why a 'Premium' Car Spark Plug Can Wreck Your Generator
- What's Actually Inside Your Generator's Oil Filter (It's Not Just a Tin Can)
- The Most Damaging Two Seconds in Your Generator's Life
- The Escape Hatch Inside Your Generator's Oil Filter
- Why That Miracle Oil Additive Doesn't Belong in Your Standby Generator
- Why Your Generator's Oil Looks Milky (and It's Usually Not a Blown Gasket)
- 5W-30: What Those Numbers Actually Mean for Your Generator
- What Too-Thin Oil Does to Your Generator in a Long Florida Outage
- Should Your Generator Run the Same Oil in Maine as in Florida?
- Why Your Generator Battery Reads 'Full' and Still Won't Crank
- The Forgotten Battery: The Smallest Part That Kills the Most Generators
- What Really Happens If You Skip a Year of Generator Maintenance
- Why the Yearly Generator Service Plan Quietly Assumes You'll Never Lose Power
- What a Real Generator Service Includes vs a "$95 Oil Change"
- The 'Bless and Bolt' Generator Service: How to Tell You Got Robbed
- Should You Pressure Wash Your Standby Generator? Read This First
- Why a Generator That Runs 10 Minutes a Week Still Needs Service
- The Warranty Says Ten Years. So Why Won't Anyone Come Fix It?
- Your Panel Says 200 Amps. The Generator Makes About 90. Does Half Your House Go Dark?
- Does Posting Your Dead Generator Online Actually Get It Fixed Faster?
- Your Generator Engine Died Under Warranty. So Why Are You Still in the Dark?
- Your Propane Tank's 10-Foot Rule Isn't Measured From Where You Think
- The $6,000 Portable That Acts Like a Standby — and Where the Plan Breaks
- Is a Variable-Speed Standby Generator Worth Paying More For?
- Why Buying Through a High-Volume Dealer Gets Your Warranty Parts Faster
- When Do You Stop Fixing an Old Whole-Home Generator?
- Kohler vs Generac: Does One Sensor Really Justify Switching Brands?
- $300 for One Oil Change? Do the Math Before You Sign the Generator Service Contract
- The Generac Service Kit vs. Buying Your Own Parts: What's Really in the Box?
- Your Battery Reads a Healthy 12.6 Volts and Still Won't Crank — The Test Your Voltmeter Can't Do
- A Tech Says Your Generator Sits Too Close to the House. Does It Have to Move — and Who Pays?
- Your New Generator Has Never Once Run. Is It a Lemon, and Who Has to Fix It?
- Can You Legally Install Your Own Standby Generator in Florida?
- Your Brand-New Generator Cranks but Won't Fire? The Install Step Everyone Misses
- Two 'Identical' Generators, One Quiet Maintenance Bill — It's Hiding in the Valves
- Does Your Generator Warranty Start When You Buy It — or When It Was Installed?
- If You Change Your Own Oil, Does the 10-Year Generator Warranty Still Count?
- You Hired a Licensed Electrician for the Generator. Did Florida Want an Electrical Contractor?
- Should the Nearest 24-Hour Dealer Pick Your Generator Brand? What Florida Owners Actually Say
- Before You Spend Five Figures, Look Up How Often Your Street Actually Loses Power
- Your Generator's Warranty Is Registered. Your Transfer Switch Might Not Be.
- What Your Generator Warranty Quietly Leaves Out — Starting With the Battery
- One Generator, Three Permits: What a Florida Standby Install Really Triggers
- Your New Generator's WiFi Can't See Your WiFi — and the Fix Costs Extra
- How to Read a Generator Install Quote Before the 'Extras' Ambush You
- Champion vs. Generac for a Florida Home: What the Budget Standby Actually Costs You
- Financing a Standby Generator: Does the Monthly Payment Erase the Reason You Bought It?
- The Part That Keeps Failing in Your Generac Isn't the Part They Keep Replacing
- Your Generator's Engine Failed at 77 Hours, Right After the Warranty. Now What?
- Your 5-Year Generator Warranty Isn't Five Equal Years
- Bury the Propane Tank or Live With the 'Submarine' in the Yard?
- The Company That Sells You a Generator Isn't Always the One That Fixes It
- Worried the generator with real buttons is going away? Here's what's actually disappearing
- The Tech Swapped Your Generator Battery on a No-Start. Did You Actually Need One?
- Air-Cooled vs Liquid-Cooled Standby Generators in Florida: Which One Survives the Summer?
- Aluminum vs. Steel Generator Enclosure: Which One Survives Florida Salt Air?
- That Pricey "Service-Rated" Transfer Switch: Do You Actually Need It?
- A Tech Swapped a $2,000 Board and the Generator Still Won't Run — Now Who Pays?
- Why Veteran Florida Generator Owners Keep a Spare Brain on the Shelf
- When Your Generator's Starter Dies, Does the Cheap One Come Back to Bite You?
- Your New Generator Threw Code 5100 and the Dealer Said "Wait for the Update." Here's What That Actually Means.
- Why Your Generator Doesn't Need to Run the Whole House at Once
- Whole House Generator Financing in Florida: Why "0%" Isn't the Cheapest Way to Pay
- Whole-Home Generator Financing in Florida: Why the Sticker Price Isn't the Number That Matters
- Someone's on Oxygen at Home — Does That Change Which Generator You Buy?
- Red and Yellow Lights on a Brand-New Generator? Did Your Installer Forget the Oil?
- A Florida Law Changed What Your HOA Can Do About Your Generator
- The $2,000 Generator Install Price Is Real. It's Also Only the Parts.
- Standby Generator in Jupiter: Why Two Identical Units Survive the Same Storm Differently